{"product_id":"starter-take-off-16","title":"Starter Take Off 16mm","description":"\u003ch3 class=\"ds-markdown-paragraph\"\u003e\u003cstrong\u003e\u003cspan\u003eWhat It Does\u003c\/span\u003e\u003c\/strong\u003e\u003c\/h3\u003e\n\u003cp class=\"ds-markdown-paragraph\"\u003e\u003cspan\u003eA starter take off (also called a start connector) is the fitting that begins a drip lateral from a rigid mainline. The mainline is usually PVC or HDPE pipe. \u003c\/span\u003e\u003c\/p\u003e\n\u003cp class=\"ds-markdown-paragraph\"\u003e\u003cspan\u003eThe starter take off inserts into a hole drilled in the mainline. The barbed end accepts the 16mm drip lateral. This creates the transition from rigid pipe to flexible drip tubing.\u003c\/span\u003e\u003c\/p\u003e\n\u003ch3 class=\"ds-markdown-paragraph\"\u003e\u003cstrong\u003e\u003cspan\u003eHow to Install\u003c\/span\u003e\u003c\/strong\u003e\u003c\/h3\u003e\n\u003cp class=\"ds-markdown-paragraph\"\u003e\u003cspan\u003eFirst, drill a hole in the mainline using a hand drill punch. The hole size must match the starter take off. For a 16mm take off, use a 16mm bit. \u003c\/span\u003e\u003cspan\u003eRemove any plastic shavings from the hole. \u003c\/span\u003e\u003c\/p\u003e\n\u003cp class=\"ds-markdown-paragraph\"\u003e\u003cspan\u003ePush the starter take off into the hole until the flange seats firmly against the pipe wall. You may need to twist slightly while pushing. The flange should be flush with the outside of the pipe. \u003c\/span\u003e\u003c\/p\u003e\n\u003cp class=\"ds-markdown-paragraph\"\u003e\u003cspan\u003eThen push the 16mm drip line onto the barbed end. Push until the tubing covers all barbs, about 15 to 20mm. If the tubing is stiff, warm the end in hot water or sunlight. No glue, no clamps.\u003c\/span\u003e\u003c\/p\u003e\n\u003ch3 class=\"ds-markdown-paragraph\"\u003e\u003cstrong\u003e\u003cspan\u003eGrommet Use\u003c\/span\u003e\u003c\/strong\u003e\u003c\/h3\u003e\n\u003cp class=\"ds-markdown-paragraph\"\u003e\u003cspan\u003eSome installations require a \u003ca href=\"https:\/\/shop.irrihub.com\/products\/rubber-black-16mm\" target=\"_blank\" title=\"Grommet rubber 16mm\" rel=\"noopener\"\u003erubber grommet\u003c\/a\u003e between the mainline hole and the starter take off. The grommet seals the gap and prevents leaks. \u003c\/span\u003e\u003c\/p\u003e\n\u003cp class=\"ds-markdown-paragraph\"\u003e\u003cspan\u003eIf you have a grommet, insert it into the hole first, then push the starter take off through the grommet. The double lip grommet grips both sides of the pipe wall. Use a grommet when the mainline is thin wall or when the hole is slightly oversized.\u003c\/span\u003e\u003c\/p\u003e\n\u003ch3 class=\"ds-markdown-paragraph\"\u003e\u003cstrong\u003e\u003cspan\u003ePressure and Leak Prevention\u003c\/span\u003e\u003c\/strong\u003e\u003c\/h3\u003e\n\u003cp class=\"ds-markdown-paragraph\"\u003e\u003cspan\u003eThe starter take off seals by compression. At pressures up to 3 bar (about 45 PSI), the seal holds. \u003c\/span\u003e\u003c\/p\u003e\n\u003cp class=\"ds-markdown-paragraph\"\u003e\u003cspan\u003eIf you see water leaking around the base of the fitting, the hole may be too large or the flange may not be fully seated. Remove the fitting, check the hole size, and reinstall. \u003c\/span\u003e\u003c\/p\u003e\n\u003cp class=\"ds-markdown-paragraph\"\u003e\u003cspan\u003eIf the leak continues, add a rubber grommet or replace the mainline section.\u003c\/span\u003e\u003c\/p\u003e\n\u003ch3 class=\"ds-markdown-paragraph\"\u003e\u003cstrong\u003e\u003cspan\u003eRemoval\u003c\/span\u003e\u003c\/strong\u003e\u003c\/h3\u003e\n\u003cp class=\"ds-markdown-paragraph\"\u003e\u003cspan\u003eTo remove a starter take off, twist and pull gently. If it is stuck, cut the mainline pipe at the fitting location and replace the section. \u003c\/span\u003e\u003c\/p\u003e\n\u003cp class=\"ds-markdown-paragraph\"\u003e\u003cspan\u003eStarter take offs are designed for one‑time use in most cases; removal can damage the flange or the pipe hole.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp class=\"ds-markdown-paragraph\"\u003e\u003cspan\u003eIrriHub provides reliable irrigation and farm systems for small and medium‑scale farmers across Kenya. For help choosing the right product for your farm, reach out to us directly. Call us: +254 729 717 881. Visit our store: Shubham Complex, Old Mombasa Rd.\u003c\/span\u003e\u003c\/p\u003e","brand":"IRRI HUB KE","offers":[{"title":"Default Title","offer_id":43037636296809,"sku":"STARTER TAKE OFF 16MM","price":10.0,"currency_code":"KES","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0667\/8167\/5625\/files\/starter.png?v=1774420501","url":"https:\/\/shop.irrihub.com\/products\/starter-take-off-16","provider":"Irri-hub","version":"1.0","type":"link"}